樂清市谷本電氣有限公司

概述  Outline

HXGN □ -12（SF6）型單元式交流金屬封閉環網開關設備（以下簡稱環網柜）是我們?cè)谝M(jìn)國外技術并按照國內農電及城網改造之要求而自行設計、研制成功的新高壓電器產品。各項技術性能指標全部達到 IEC298 和 GB3906 標準。 

環網柜的主開關、操作機構及元器件采用原裝件或采用部件國內組裝生產的 SFL-12/24 型開關設備，也可根據用戶需要配裝原裝 HAD/US 型 SF。斷路器或 VD4-S 型真空斷路器，其操作方式分為手動、電動兩種。 

柜體經數控機床加工后鉚接而成，防護等級達到 IP3X，并有可靠的機械聯鎖和防誤操作功能。本產品具有體積小、重量輕、外形美觀、操作簡便、長壽命、高參數、無污染、少維護等的特點。 

HXGN □ -12(SF6) Unit type AC metal-enclosed ring main unit(hereafter refer to as ring net cabinet) is a new generation of high-pressure electric appliance product designed and developed independently by our own company according to the requirement of the domestic agricultural electricity and the city net transformation after introduction of overseas advanced technology. Each technical performance index completely reaches the IEC298 and GB3906 standard. 

The loop-net cabinet s main switch, the operating mechanism and the components is made of the  Corporation original piece or the SFL-12/24 switch equipment imported overseas and ass-embled at home. We can also install the Corporation original piece of HAD/US type SF according to the request of users. The circuit breaker or the VD4-Svacuum circuit-breaker divide into two kinds: be operated manually and electrically according to the operating mode. 

The cabinet body is riveted after processed by numerical control machine tool with reliable mechanical interlocking and the misoperating prevention function. The protection grade reaches IP3X.This product has the remarkable characteristics such as the small volume, light weight, artistic appearance, simple operation, long life, high parameter with no pollution and little maintenance.

使用環境條件   Use environmental conditions

1、海拔不超過 2000m 

2、周圍空氣溫度：上限 +40℃下限 -25℃ 

3、相對溫度：日平均值不大于 95%，月平均值不大于 90% 

4、周圍空氣不受腐蝕性氣體或可燃性氣體、水蒸氣等明顯污染 

5、無經常性的劇烈振動

1. The altitude should not exceed 2000m.

2. Surrounding air temperature: -25℃ ~+40℃

3. Relative temperature: the daily average value is not higher than 95%, the the monthly average value is nothigher than 90%

4. Surrounding air without caustic gas or ignitable gas, steam and other obvious pollution

5. Without fierce vibration

型號及含義  Model and meaning

用途  use

HXGN □ -12（SF6）型單元式交流金屬環網開關設備，適用于交流 50Hz、12kV 中，作為電能的接受和分配之用。

HXGN □ -12 (SF6) unit type exchange metal ring- net switching equipment, is suitable to exchange 50Hz、12kV , searving as device of receiving and distribution of electrical energy.

主要技術參數  The main technical parameters

結構特點及工作原理   Structural features and working principle

 產品外形結構見圖 1、圖 2，安裝尺寸如圖 3 所示。本環網柜是以空氣為絕緣介質的，主要配裝 ZFN □ -10/630 型真空負荷開關，主要方案有進線柜和出線柜等。 

1. 進線柜方案 

柜內主回路有一臺 ZFN □ -10/630 型真空負荷開關，它配裝有隔離刀、酌情還配裝接地刀所組成，三者共裝在一個機架上，并互有聯鎖。因此可實現 接通母線、隔離、接地三個工位的操作，柜內還可靈活配裝 CT、PT 等元件。 

2. 出線柜方案

柜內主回路有一臺 ZFN □ -10/630 型真空負荷開關和帶撞擊器的熔斷器 ( 有隔離開關的作用 ) 及接地刀所組成，也可實現三工位操作，柜內還可靈活 配裝 CT/PT 和 ZNO 避雷器等元件，因此有時可省去計量柜。進、出線柜均配有與接地開關聯鎖的絕緣防護隔板，柜內各開關與隔板及柜門間采用機械 聯鎖，并達到“五防”要求，柜體外殼防護等級為 IP2X。

The outline structure of the product is referred to as diagram 1 and diagram 2; the installation dimension is referred to as diagram3. This ring network type cabinet makes air as the insulating medium,mainly assembled with ZFN □ -10/630 type vacuum load switch. And there are two cabinet schemes - incoming cabinet and outgoing cabinet. 

1.Incoming cabinet scheme

   There is a ZFN □ -10/630 type vacuum load switch on the main circuit inside the cabinet with isolating knife, and grounding knife conditionally. The three of them are all installed in one machine stand and there are interlocks among them, so that it is realized to connect the operation of three working stations of bus, isolation and grounding. Inside the cabinet the com-ponents such as CT, PY are available.

2.Outgoing cabinet scheme

   ZFN □ -10/630 type vacuum load switch, fuse with striker (used as isolating switch) and grounding knife on the main circuit inside the cabinet, and the three working stations oper-ation can be realized. Inside the cabinet the components such as CT/PT and ZNO arrester are available, so the metering cabinet can be omitted. Inside the incoming cabinet and out-going cabinet, there is insulating protecting baffle interlocked with grounding switch. And inside the cabinets ,the mechanical interlocks are adopted between each switch and baffle as well as the cabinet door with the requirement of “five-prevention” and IP2X of the protection degree of the cabinet enclosure.

吊運、安裝、調試和熔斷器的更換  Lifting, installation, commissioning and replacement of fuses

1. 吊運 

    吊運前按規定進行開箱前的檢查。柜體吊運時按作業標記要求，小心輕放、防震等。 

2. 安裝 

    開箱后，檢查柜體及柜內元件是否完好，動作是否正常，是否受潮等，在確認無誤后，方可進行安裝。 

3. 調試 

    如發現柜內元件達不到其技術要求或聯鎖不到位時，需按下列過程調試： (1) 對負荷開關和接地或隔離開關，可通過調節拉桿長度和變換拉桿與操作桿角度和位置來達到技術要求。 (2) 若有聯鎖不到位時，可微調相應的操作拉桿長度來改變聯鎖孔的位置，使聯鎖到位。 

4. 更換熔斷器 

    必須嚴格按停電順序操作，將負荷開關分閘，然后打開熔斷器到隔離位置，并將接地開關合上，在插入絕緣防護隔板后，柜門方可打開，才能進 行更換熔斷器。

1. Handling 

    Before handling, undertake check before opening the cabinet according to the regulations. When thecabinet is handling delivered, it's a must to operate according to the operation marking demands.Handle with care and without shake.

2. Installing 

    After opening the cabinet, check whether the cabinet body and the components inside are good,whether they work normally, and whether they are moistened. Only after definite confirmation can the installation be undertaken. 

3. Debugging

    It's necessary to have a debugging according to the following steps if the components inside thecabinet don't meet the technical requirements or the interlocks don't locate well: (1) For the load switch, grounding switch or isolating switch, you can make them meet the technical demands by adjusting the drag rod length, changing the angle and position of drag rod and operating rod. (2) If there is any interlock that doesn't locate well, you can make it locate by fine adjusting relevant operating rod length to change the position of interlock hole.

4. Fuse replacing 

    It must operate strictly according to the sequence of power off. First, turn off the load switch, turn on the fuse to the isolating position and then turn on the grounding switch. Only after plugging the insulating protecting baffle can the cabinet door be opened and can the fuse be replaced.

使用與故障處理   Use and troubleshooting

1. 使用 

    請務必嚴格按照下列步驟操作，否則易造成損害。

(1) 負荷開關的操作順序 

 a 合閘：當負荷開關處于分閘狀態時，將操作手柄插入負荷開關操作孔內順時針轉動 ( 約 180 度 )，使其合閘。 

 b 分?jǐn)喈?dāng)負荷開關處于合閘狀態時，可由手動脫扣按鈕或脫扣電磁鐵操作使負荷開關分閘，對配有帶撞擊器的熔斷器的負荷開關，熔斷器熔斷后，其 撞擊器也可使負荷開關分閘。

(2) 停電操作順序 

 a 將負荷開關分閘，使它與隔離和接地開關之間的聯鎖解除。 

 b 將操作手柄插入隔離和接地開關操作孔內，按順時針?lè)较蜣D(zhuǎn)動 ( 約 90 度 )，隔離刀被打開。 

 c 再按順時針?lè)较蜣D(zhuǎn)動 ( 約 90 度 ) 后，接地開關快速閉合。 

 d 插入絕緣隔板，使門聯鎖解除。 

 e 開門檢修。 

(3) 送電操作順序 

 a 關閉柜門。 

 b 抽出絕緣隔板，柜門鎖住。 

 c 將操作手柄插入隔離和接地開關操作孔內，逆時針轉動 ( 約 90 度 )，使接地開關分?jǐn)唷?nbsp;

 d 對負荷開關進行操作，合閘送電。

2. 故障處理 

    環網柜在工作過程中，如果出現緊固件松動，機械部分潤滑不良，真空滅弧室真空度下降等故障，在停電后采用緊固、加潤滑劑、打耐壓等方法來檢 查和消除以上故障。

1.Operation 

   Please operate strictly according to the following steps, otherwise some damage may be caused. 

(1) Operating sequence of load switch 

  a. Switch-on: When the load switch stays on, plug the operating handle into the operating hole of the load switch and turn it clockwise (about  180° ) to make it stay on. 

  b. Switch-off: When the load switch stays on, manually operate the tripping button or the tripping electromagnet to make the load switch stay off. For the load switch with fuse striker, after the fuse is fused, the striker can make the load switch stay off. 

(2) Operating sequence of power off 

  a. Turn off the load switch to unlock the interlock between the isolating and grounding switches. 

  b. Plug the operating handle into the operating hole of the isolating and grounding switches and turn it clockwise (about 90° ) to open the isolating knife. 

  c. Turn again clockwise (about 90° ) to turn off the grounding switch rapidly. 

  d. Plug the insulating baffle to unlock the door interlock. 

  e. Open the door and maintain.

(3) Operating sequence of power transmission 

  a. Close the cabinet door. 

  b. Extract the insulating baffle and lock the cabinet door. 

  c. Plug the operating handle into the operating hole of the isolating and grounding switches and turn itanticlockwise (about 90° ) to turn off the grounding switch. 

  d.Operate the load switch and turn it on to transmit the power. 

2. Fault treatment 

   During the operation of the ring network type cabinet, if there is any fault, such as loose fasteners, bad lubrication of mechanical parts and reduced vacuum degree in the vacuum interrupter, etc. After the power off, check and remove the faults by fastening, adding lubricant and adding withstand voltage, etc.

維修與修理   Repair and repair

1. 開箱后，應對絕緣件進行檢查，對確已受潮的元件，應將其拆下，放入 70-80℃的烘箱內，烘 48 小時后，取出裝上重新調試。 

2. 產品儲放期間，如發現受潮或腐蝕，應立即進行清理，清理后做好防護處理。 

3. 運行中的環網柜應進行定期維修檢查。 

   (1) 真空滅弧室的真空度； 

   (2) 觸頭磨損情況； 

   (3) 機械緊固件是否松動； 

   (4) 開距超程等機械電氣參數； 

   (5) 操作轉動是否靈活； 

   (6) 聯鎖是否可靠； 

   (7) 零部件，特別是絕緣件是否清潔。 

4. 下列情況時，應對環網柜進行全面檢查和調試； 

   (1) 每年一次的例行檢查和清潔工作；

   (2) 負荷開關每動作 2000 次后。

1. After the cabinet is open, check all of the insulation pieces and disassemblethe damp ones, put them into 70-80℃ drying box, and take out for debugging again after 48 hours drying. 

2. If the product is damp or rusty during the storage, please clean it at once and protect it well. 

3.Maintenance and repair should be done to ring network cabinet during operation

  (1).Vacuum extent of vacuum arc-extinguishing room 

  (2).Contact abrasion degree 

  (3).Whether the fastening pieces are loose or not; 

  (4).Mechanical electric parameter such as open travel, over travel. 

  (5).Whether the running is flexible or not; 

  (6).Whether the interlock is reliable or not;

  (7).Whether all of the parts are clean, especially for insulation fittings. 

4.Do overall examination and debugging to ring network cabinet in following conditions: 

  (1).Routine examination and cleaning for every

  (2).After every 2000 times operation of load switch

儲存  Store

環網柜應儲存在干燥通風，溫度在 -30℃ ~+40℃的倉庫中。

Ring network cabinet should be stored in the dry and ventilated warehouse with temperature of -30℃ ~+40℃ .

隨機文件  Random document 

1. 產品合格證 Certificate of quality 

2. 安裝使用說明書 Installation and operation instruction 

3. 裝箱單 Packing list 

4. 隨機附件清單 Appending accessories list 

5. 二次接線圖 Secondary connection diagram

環網柜安裝   Ring cabinet installation 

組合電器柜   Combination electrical cabinet 

負荷開關柜   Load switch cabinet